Cisco Cable Box Remote Codes

Do you have a Cisco cable box and need the remote codes to program it? This post provides the remote codes for Cisco Cable Box. Key in the digits below using the numeric key codes on your remote control.

Cisco All-in-One Cable Box Remote Codes

  • 0498
  • 0496
  • 0497
  • 0567
  • 0506
  • 0543
  • 0535
  • 0512
  • 0509
  • 0466
  • 0455
  • 0496

Dynex 1593, 1589, 1507, 1609
Emerson 1465, 1020, 1043, 1135, 1028, 1023, 1036, 1333, 1024, 1118, 1595,

GE 1000, 1094, 1049, 1135, 1333, 1021, 1063, 1512, 1068, 1558, 1380

Hitachi 1030, 1522, 1051, 1001, 1098, 1102, 1363, 1086, 1490, 1344, 1206,
Insignia 1255, 1519, 1024, 1232, 1437, 1507, 1593, 1595, 1596, 1601, 1436
JVC 1023, 1092, 1054, 1055, 1169, 1526, 1026, 1080, 1615
LG 1255, 1020, 1333, 1257, 1539, 1146, 1584, 1638, 1303, 1723, 1294, 1293. Magnavox 1633, 1576, 1047, 1049, 1061, 1632, 1457, 1595, 1027, 1300, 1145,
Memorandum 1043, 1023, 1032, 1333, 1001, 1022, 1593, 1121, 1305, 1165, 1725
Mitsubishi 1005, 1009, 1032, 1333, 1018, 1535, 1540, 1153, 1279, 1284, 1282,
Panasonic 1466, 1096, 1469, 1049, 1169, 1554, 1010, 1564, 1385, 1305, 1165,
Philips Magnavox 1772
Philips 1633, 1576, 1047, 1126, 1239, 1549, 1337, 1632, 1234, 1785, 1226,
Pioneer 1469, 1102, 1149, 1377, 1336, 1339, 1342, 1343, 1346, 1338, 1345,
Polaroid 1565, 1111, 1639, 1391, 1604, 1596, 1502, 1371, 1583, 1393, 1407,
RCA 1144, 1000, 1094, 1049, 1009, 1640, 1613, 1610, 1596, 1459, 1386
Samsung 1314, 1073, 1156, 1333, 1061, 1161, 1173, 1547, 1530, 1172, 1169,
Sansui 1023, 1024, 1064, 1593, 1090, 1121, 1382, 1114, 1256, 1263, 1251,
Sanyo 1047, 1043, 1095, 1527, 1062, 1380
Sharp 1138, 1009, 1011, 1025, 1064, 1350, 1537, 1153, 1378, 1248, 1247,
Sony 1037, 1219, 1534, 1574, 1090, 1388, 1408, 1515, 1814, 1812
Sylvania 1465, 1047, 1061, 1024, 1059, 1554, 1150, 1464, 1145, 1300, 1027,
Toshiba 1159, 1043, 1058, 1223, 1255, 1073, 1222, 1532, 1340, 1550, 1169,
Vizio 1829, 1433, 1181, 1184, 1042, 1824, 1289, 1625, 1822, 1823, 1831,
Westinghouse 1515, 1135, 1184, 1544, 1555, 1178, 1567, 1616, 1816, 1198. Zenith 1037, 1255, 1094, 1020, 1023, 1333, 1061, 1522, 1051, 1015, 1118.

Also read the remote codes on the digital converter box

How to program the Cisco Remote To Cable Box

Step 1. Make sure to turn on your cable box.

Step 2. Hold the remote to face your Cisco cable box.

Step 3 . Hold down the button “CBL” on the remote control for a couple of seconds. The button CBL It is the Components button for Cable box of your remote control. Release the button when the small component LED light turns on the button.

Step 4. Enter the correct 3-digit code for the brand of your cable box. The remote codes have been listed earlier in this article.

Step 5. Press the power button. If your device turns off, it means you have the correct code. If not, try the following code. You can also try it with the Volume buttons.

Step 6. Finally save the codes by pressing the Component button again. That is, press the “CBL” button again until the little LED button blinks twice to show that your codes have been saved.

How to program the Cisco Remote To Cable Box (Second method)

Step 1. Make sure to turn on your cable box.

Step 2. Hold your Cisco remote so that it is facing your cable box.

Step 3 . Hold down the On / off and the Ok / Sell simultaneously for a couple of seconds, until the button “CBL” it turns on.

Step 4. Press and hold the button “CBL” on the remote control for a couple of seconds.

Step 5. Enter the correct 3-digit code for the brand of your cable box. The remote codes have been listed earlier in this article. If your device is turned off, it means that you have the correct code. If not, try the following code. You can also try it with the volume buttons.

It also reads the universal codes from the Sansui TV remote control

Step 6. Finally save the codes by pressing the CH + button again until the little LED button blinks twice to show that your codes have been saved.

If there is any other code you need, please use our search box to check the code. You can also contact us using the comment section or send us a message. We will take care of the code and post here.